AXIAL COMPRESSION BEHAVIOUR OF REINFORCED CONCRETE COLUMNS WITH 3D-PRINTED CONCRETE AS PERMANENT FORMWORK
| dc.contributor.advisor | Butler, Liam J. | |
| dc.contributor.author | Rajenthirakumar, Subakaran | |
| dc.date.accessioned | 2026-11-06T16:12:42Z | |
| dc.date.available | 2026-11-06T16:12:42Z | |
| dc.date.copyright | 2026-07-21 | |
| dc.date.issued | 2026-11-06 | |
| dc.date.updated | 2026-11-06T16:12:41Z | |
| dc.degree.discipline | Civil Engineering | |
| dc.degree.level | Master's | |
| dc.degree.name | MASc - Master of Applied Science | |
| dc.description.abstract | This study investigated the axial compressive behaviour of reinforced concrete columns using 3D-printed concrete (3DPC) as permanent formwork, focusing on load sharing among materials and 3DPC behaviour. It included three phases: Phase 1 assessed 3DPC material behaviour under compression using cubes and prisms saw-cut from a 3DPC wall, revealing isotropic compressive behaviour in the two tested directions through statistical analysis. The prism's strength was 21% lower than the cubes, with a modulus of elasticity differing by only 3%. Phase 2 compared the theoretical axial stiffness derived using the modulus of elasticity determined through cubes and prisms to the axial stiffness of 320 mm tall 3DPC cylindrical shell specimens. This resulted in an overestimate of axial stiffness by 73% and 79% for cubes and prisms, respectively, compared with the experimental axial stiffness determined from the load-deformation response of the cylindrical shells under uniaxial compression. Phase 3 examined small-scale circular columns (250 mm diameter, 240 mm height) and large-scale square columns (350 mm section width, 1040 mm height), with similar conventionally cast specimens made from the same concrete mix proportion. Due to the capacity of the hydraulic actuator used for the setup, the square columns were loaded to 1000 kN, while circular columns were tested to failure. The circular 3DPC columns maintained intact printed formwork up to failure but had compressive strengths 4.5% lower than cast-in-place columns, with 35% reduced initial axial stiffness compared with cast-in-place columns. Two print layouts for the square columns (47PC with 47% printed concrete and 60PC with 60% printed concrete) showed initial stiffness reductions of 47.5% and 45.4%, respectively, compared to control specimens. A modified fibre section model predicted axial load resistance and was validated against cast-in-place specimens, with a maximum error of 2.1%. Three constitutive models for printed concrete were evaluated, with the cylindrical shell model showing the most accuracy, yielding maximum errors of 8.1% for 47PC and 5.4% for 60PC. These findings indicate that 3DPC as permanent formwork is a viable alternative to conventional methods and remains structurally intact up until failure. Further investigations are recommended to validate the proposed model across the complete load–deformation response. | |
| dc.identifier.uri | https://hdl.handle.net/10315/44307 | |
| dc.language | en | |
| dc.rights | Author owns copyright, except where explicitly noted. Please contact the author directly with licensing requests. | |
| dc.subject | Civil engineering | |
| dc.subject.keywords | 3DPC | |
| dc.subject.keywords | Reinforced concrete columns | |
| dc.subject.keywords | Axial compression behaviour | |
| dc.subject.keywords | Fibre section modelling | |
| dc.subject.keywords | Permanent formwork | |
| dc.subject.keywords | Additive concrete construction | |
| dc.title | AXIAL COMPRESSION BEHAVIOUR OF REINFORCED CONCRETE COLUMNS WITH 3D-PRINTED CONCRETE AS PERMANENT FORMWORK | |
| dc.type | Electronic Thesis or Dissertation |
Files
Original bundle
1 - 1 of 1
Loading...
- Name:
- Rajenthirakumar_Subakaran_2026_MASc.pdf
- Size:
- 122.67 MB
- Format:
- Adobe Portable Document Format