YorkSpace
    • English
    • français
  • English 
    • English
    • français
  • Login
Search 
  •   YorkSpace Home
  • Canadian Society for Mechanical Engineering (CSME) International Congress
  • Search
  •   YorkSpace Home
  • Canadian Society for Mechanical Engineering (CSME) International Congress
  • Search
JavaScript is disabled for your browser. Some features of this site may not work without it.

Search

Show Advanced FiltersHide Advanced Filters

Filters

Use filters to refine the search results.

Now showing items 1-10 of 37

  • Sort Options:
  • Relevance
  • Title Asc
  • Title Desc
  • Issue Date Asc
  • Issue Date Desc
  • Results Per Page:
  • 5
  • 10
  • 20
  • 40
  • 60
  • 80
  • 100
Thumbnail

Thermal Management of Electrical and Electronic Systems Using PCM 

Alomair, Yazeed A.; Alomair, Muath; Tasnim, Syed; Abdullah, Hussein A.; Mahmud, Shohel (CSME-SCGM, May-18)
The present experimental research investigates transient thermal performance of a PCM-based thermal management system for cooling electronics components. The proposed system consists of a heatsink that is submerged into ...
Thumbnail

Energy Transfer Mechanisms In The Ranque-Hilsch Vortex Tube 

Dyck, Nolan; Straatman, Anthony (CSME-SCGM, May-18)
The Ranque-Hilsch Vortex Tube (RHVT) is a small tube without any moving parts receiving compressed air from a tangential inlet and exhausting cold air from a small hole at one end of the tube while exhausting hot air from ...
Thumbnail

The Design Of Infrared Mirror Coatings For The Enhanced Performance Of Incandescent Lighting 

Rostami, Mohsen; Talebzadeh, Nima; O'Brien, Paul (CSME-SCGM, May-18)
Herein we present the design of infrared mirror coatings for the enhanced performance of incandescent lighting. We consider single and stacked dielectric mirrors comprised of alternating layers of TCO and SiO2 nanoparticle ...
Thumbnail

Analysis Of Thermal Losses In Air-Water Interfacial Solar Heating Systems 

Wang, Shuzhe; O'Brien, Paul G. (CSME-SCGM, May-18)
This paper reports a numerical analysis of solar-driven seawater desalination systems with two configurations: a floating photo-thermal film at the air-water interface with and without an insulation layer located beneath ...
Thumbnail

Preparation and Properties of Nanoparticle-enhanced Composite Phase Change Material with Ceramic Porous Media 

Li, Runfeng; Zhou, Yang; Duan, Xili (CSME-SCGM, May-18)
Nanoparticle-enhanced tailing-paraffin composite phase change material (NCPCM) is fabricated by spontaneous melt infiltration. Industrial waste-iron tailing is used as raw material to prepare ceramic porous carrier with a ...
Thumbnail

Investigation into the Influence of Fused Deposition Modeling (FDM) Process Parameters on the Thermal Properties of 3D-Printed Parts 

Elkholy, Ahmed; Kempers, Roger (CSME-SCGM, May-18)
The mechanical properties of 3D-printed parts have been extensively studied and the effects of printing parameters on them have been investigated. However, there are limited reliable data for the thermal properties of the ...
Thumbnail

Motion Of Pigments In Thin Paint Films 

Curak, Marina; Saranjam, Nazli; Chandra, Sanjeev (CSME-SCGM, Nov-18)
When thin paint layers are exposed to heat, evaporation of the solvent begins, and significant movement within the paint film occur, causing temperature and concentration gradients. A clear coat paint was used, which had ...
Thumbnail

Kinetics Analysis Of Multi-Segment Trunk After Experimental Errors Minimization 

Noamani, Alireza; Vette, Albert H.; Preuss, Richard; Popovic, Milos R.; Rouhani, Hossein (CSME-SCGM, May-18)
A two-dimensional analytical heat conduction model of an annular composite fin has been carried out. The composite fins composed of a porous polyethylene core, a square aluminum insert, and metallic zinc coating layers, ...
Thumbnail

Thermal And Hydraulic Performance Of A Novel Evaporator Coil For Refrigeration Systems 

Elkady, Hossam; Elsharqawy, Mostafa; Saad, Sameh; Ahmed, Kazi (CSME-SCGM, May-18)
With increasing energy cost and constraints on emission standards, there is a strong need to reduce energy consumption and/or increase equipment efficiency. Refrigeration systems are the third largest use of electricity ...
Thumbnail

A Model To Predict The Residual Layer Thickness In The Injection Molding Process 

Mollaabbasi, Roozbeh; Behzadfar, Ehsan (CSME-SCGM, May-18)
The effects of the wall temperature on the residual layer thickness of the polymers are studied numerically in the filling process in the injection molding process. A lubrication approximation model is developed to furnish ...
  • 1
  • 2
  • 3
  • 4

All items in the YorkSpace institutional repository are protected by copyright, with all rights reserved except where explicitly noted.

YorkU LogoContact Us | Send Feedback
link to sitemap

 

Browse

All of YorkSpaceCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsThis CommunityBy Issue DateAuthorsTitlesSubjects

My Account

LoginRegister

Discover

AuthorChandra, Sanjeev (4)Duan, Xili (3)Kempers, Roger (3)Mahmud, Shohel (3)Abdullah, Hussein A. (2)Alomair, Muath (2)Elkholy, Ahmed (2)Gibbons, Michael (2)O'Brien, Paul G. (2)Tasnim, Syeda (2)... View MoreSubject
Heat Transfer (37)
Fluid Mechanics (11)Advanced Energy Systems (9)Materials Technology (8)Computational Mechanics (7)Engineering Analysis & Design (5)Manufacturing (5)Environmental Engineering (4)Analytical model (2)Biomechanics and Biomedical Engineering (2)... View MoreHas File(s)Yes (37)

All items in the YorkSpace institutional repository are protected by copyright, with all rights reserved except where explicitly noted.

YorkU LogoContact Us | Send Feedback
link to sitemap